Ako zabrániť poškriabaniu hliníkového disku

Ako zabrániť poškriabaniu hliníkového disku

Všetci vieme, že hliníkové disky sú hliníkové plechy a hliníkové cievky, ktoré sú vyrobené z hliníkového kotúčového kovu ako suroviny, and the discs need to add some additives on the basis of pure aluminum to form national standard 1050 hliníkové disky, 1060 hliníkové disky alebo 3003 hliníkové disky. Aluminum discs are made by punching and cutting aluminum plates. Preto, discs are easily scratched during transportation or use. Preto, we need to know that to prevent aluminum discs from being scratched, we should pay attention to the following three key points.

Aluminum discs are prototype products obtained by pressing and rolling aluminum ingots. We can know that discs can be divided into many types according to different uses, different types, and different alloy grades. Preto, aluminum discs also have different applications. So what causes the damage caused by the use of aluminum discs? Teraz, as a senior aluminum disc manufacturer, we have summarized the following three points about the direct causes of damage to the surface of aluminum discs. I hope everyone can pay attention to them when using aluminum discs.

Ako zabrániť poškriabaniu hliníkového disku

Prvé: During the kneading process of the disc, after we take the normal piece back, we need to go back and forth on the machine, and we need to hold an aluminum disc back and forth. V tomto procese, the two aluminum discs will produce metal friction, or when the aluminum disc passes through the metal flow operation, a large amount of oxidation or solid oxide film will exist or analyze on the aluminum surface, which will float on it. Týmto spôsobom, when we put the two aluminum discs together, it will cause a very large damage to the surface of the aluminum disc, so we recommend that you pay attention to this problem when operating in the middle.

Druhý: When the aluminum disc is working, it is recommended to pay attention to not carry debris. Súčasne, when making or transporting the aluminum disc, it is recommended to pay attention to not slip. In order to avoid large-scale scratches on the aluminum disc, we will make a bad prediction of the surface and effect of the aluminum disc during stamping, and feel that the aluminum disc is not effective. This is a taboo. It may have a relatively large impact at the beginning, but it is recommended to pay attention to the following issues in the later stage to avoid secondary damage to our discs.

Tretiny: Bumps caused by excessive production speed of aluminum discs. We all know that if the conveying track of the aluminum disc is too fast during the stamping process, it will cause two aluminum discs to overlap. Then the aluminum disc will be damaged and damaged on a large area due to the rapid overlap. Preto, it is recommended to pay attention to the track of the aluminum disc production, which is not easy to adjust too fast or too slow. Po druhé, in the process of transporting aluminum discs, it is especially important to pay attention to the packaging of aluminum discs, which is not too tight or too loose. It is recommended to use steel belts or plastic molds for large-area packaging, so that the surface of the aluminum disc will not be damaged or scratched, and the damage caused by the friction between aluminum discs during transportation will be prevented.

The above are the three points that the disc manufacturer introduces to you about how to prevent continuous scratches.

Aluminum discs are currently a widely used disc metal in our lives. Súčasne, aluminum discs are also one of the most economical and applicable materials. This is due to the fact that the density of aluminum discs is very low, less than half of that of steel. This is one of the reasons why aluminum discs are gradually expanding their applications in our lives, especially discs. They are particularly important in the manufacturing industries of metals, airplanes, vlaky, a lode. In the fields of kitchenware aluminum discs and lamp aluminum discs, pure aluminum relies on its softness and low strength, including its good ductility. It can be made into filaments and fried into aluminum foil, tam. It is widely used in various fields such as aluminum discs, aluminum lamps, hliníkový kuchynský riad, aluminum disc signs, and packaging industries.

More aluminum circle: https://www.aluminium-circle.cn/